Pumps · Systems · Expertise
Protect your uptime.Slash your energy bill.
Precision Fluid Solutions supplies the hydronic systems that keep your build on schedule: guaranteed performance data, 48-hour submittals, and right-first-time startup, all from one Armstrong-backed source.
Engineered selections backed by live performance data.
0%
Up to this much system energy saved with Armstrong Design Envelope vs. traditional constant-speed systems
0h
Typical submittal turnaround on stocked packages
100s
Pumps and hydronic packages supported across our territory
0/7
After-hours technical line staffed by our team
Capabilities
One call covers everything between the meter and the coil
Pump selection & sizing
Duty-point analysis, parallel pump staging, and curve-verified selections that hold their efficiency across the real operating range, not just at design.
Intelligent controls
Sensorless variable speed, Design Envelope integration, and BAS points mapped to your sequence of operations before the crate is opened.
Startup & commissioning
Factory-trained startup, controls integration, and commissioning support to get your system performing from day one.
Hydronic system design
Loop modeling, delta-T troubleshooting, air and dirt separation, expansion sizing, solving the system, not swapping the symptom.
Submittals in 24 hours
Selections, curves, dimensional drawings, and spec-compliance letters returned inside one business day on standard packages.
Lifecycle stewardship
Installed-base tracking, performance benchmarking, and planned replacement schedules so nothing fails on the coldest night of the year.
Retrofit in place
Drag the handle. That's the difference.
Most of the plants we walk into were designed for a building that no longer exists: oversized base-mounted pumps, throttled balance valves, and a 6°F delta-T. We replace them in place, usually without a shutdown longer than a weekend, and hand you an energy savings story your CFO will actually read.
- Same footprint, half the connected horsepower
- Sensorless control removes the differential pressure sensor network
- Rebate paperwork filed with your utility on your behalf
- Measured before-and-after report, not a manufacturer brochure
Representative retrofit imagery. Ask us for the metered case study from a comparable facility in your market.
Live plant simulation
Built to run. Built to last.
Design Envelope pumps on site, compact footprint, integrated intelligent controls, and performance you can watch, not just read about on a spec sheet.
- Real time pump staging as building load rises and falls
- Variable speed matches flow to demand instead of throttling away horsepower
- Sensorless control eliminates the cost and drift of field DP sensors
- Every watt saved is metered, not estimated
Drag the time slider inside the simulation to see how the plant responds hour by hour.
Live plant simulation
RunningHead vs flow · 2 pumps running
11:11
Flow
1494gpm
Head
119ft
Speed
100%
Power
44.6kW
Savings vs throttling
4%
Energy avoided
0kWh
Design day
Coil valves wide open. Both pumps sit on the design point, 1500 gpm at 120 ft.
Variable primary chilled water · 2 x 50% pumps · 1500 gpm @ 120 ft design
Sizing advisor
Budget numbers before you pick up the phone
No form gate, no waiting on a rep to call you back. Move the sliders and see the selection family, motor size, and the annual energy delta against a legacy constant speed pump.
Instant sizing
Tell us the duty point
Preliminary selection
Design Envelope 4300 vertical in-line
- Estimated shaft power
- 15.9 BHP
- Recommended motor
- 20 HP
- Annual cost, legacy constant speed
- $4,455
- Annual cost, Design Envelope
- $2,762
Projected annual savings
$1,693
≈ 5.9 metric tons CO₂e avoided per year.
Budgetary estimate only. Send it to our team and you get a stamped selection, curve, and submittal package back, typically inside one business day.
We will confirm the selection against your actual duty point, free of charge.
How we work
Five steps from bid to startup, no surprises
Walk the room
We measure the system as it runs today, flow, head, amp draw, delta-T, sequence.
Model the fix
Selections and energy models compared side by side with real utility rates.
Engineer the package
Pumps, controls, separators, and accessories delivered as one coordinated submittal.
Start it up right
Factory startup, commissioning support, and O&M training for your team.
Stay on the loop
Annual benchmarking and stocked parts so performance never quietly drifts.
2025Gold Club Award
Armstrong Fluid Technology, presented to Jarod Heppner
Recognition
We didn’t put this on the wall. Armstrong did.
In 2025, Armstrong Fluid Technology named Jarod to their Gold Club, a distinction the factory extends to a small group of partners across its network. We mention it once, plainly, because the part that matters is who is doing the recognizing: the engineers who build the equipment we put into your plant.
“One name is on the award. Behind it stands every contractor, facility engineer, and superintendent who handed us a schedule and trusted us to protect it.”
- Chosen by the manufacturer we represent
- Earned in the field, job by job
- Held by the person who walks your room
Principal manufacturer
Armstrong Fluid Technology
Armstrong builds the most intelligent fluid-flow equipment in the industry, Design Envelope pumps with onboard variable speed and sensorless control, integrated plant packages, and a demand-based control platform that keeps optimizing after startup. Precision Fluid Solutions is your local channel for the full line.
Explore the Armstrong lineDesign Envelope pumps
Vertical in-line, twin, and end-suction with integrated intelligent drives.
Plant packages
Skidded chilled and hot water plants, factory-tested before shipment.
Heat transfer
Plate & frame, shell & tube, and instantaneous domestic water heating.
Pump Manager
Cloud performance monitoring with early-warning fault detection.
Contact
Put us on your next job
Schedules, specs, a photo of a nameplate, or a rough idea on a napkin, we'll take it from there and come back with a selection and a number that wins the job.